« previous next »
Pages: [1]   Go Down

Author Topic: Thread diameters and EOM  (Read 2597 times)

Offline bimmridder

  • Gonzo Member
  • ******
  • Posts: 1889
Thread diameters and EOM
« on: April 11, 2013, 10:22:45 AM »
Not that this is anything surprising or revolutionary, but I just took a few quick readings on some mesh, same thread count, different diameter.

Coated using identical technique on Kiwo Simplex. 1-2 round
Speed 6 (Irrelevant)
Ulano Orange
Coated and dried overnight in 30% RH
Imaged with Kiwo I-Jet
Exposed on Olec 5K 65 light units
Developed with warm water pres soak and 750 PSI wash
Dried room temp (70 +/-)
measured after four hours dry time

158-48  59 EOM
156-64   24 EOM

These are all parameters used in my shop and different than yours. Just trying to show what the difference in thread diameter makes in coating a screen, and final EOM.

Logged
Barth Gimble

Printing  (not well) for 35 years. Strong in licensed sports apparel. Plastisol printer. Located in Cedar Rapids, IA

Offline alan802

  • !!!
  • Gonzo Member
  • ******
  • Posts: 3535
  • I like to screen print
Re: Thread diameters and EOM
« Reply #1 on: April 11, 2013, 11:45:36 AM »
Those numbers are almost identical to what we get between two of the same mesh counts with different diameters.  The thin threads get a much thicker eom with the same amount of work.  Most thin threads could probably be coated 1/1 and have the same eom as a regular thread that's been done 2/1.
Logged
I would rather be exposed to the inconveniences attending too much liberty than to those attending too small a degree of it -T.J.
Those who expect to reap the blessings of freedom, must, like men, undergo the fatigues of supporting it -T.P.

Offline ScreenPrinter123

  • Hero Member
  • *****
  • Posts: 863
Re: Thread diameters and EOM
« Reply #2 on: April 11, 2013, 02:33:58 PM »
Holla...!
Logged

Offline Homer

  • !!!
  • Gonzo Member
  • ******
  • Posts: 3211
Re: Thread diameters and EOM
« Reply #3 on: April 11, 2013, 09:31:48 PM »
stupid question but is there any other "thin thread" mesh besides murakami s mesh? I can't seem to get it locally anymore.
Logged
...keep doing what you're doing, you'll only get what you've got...

Offline GKitson

  • Hero Member
  • *****
  • Posts: 720
  • Just another t-shirt guy
Re: Thread diameters and EOM
« Reply #4 on: April 12, 2013, 07:43:28 AM »
Quote from: bimmridder on April 11, 2013, 10:22:45 AM
Not that this is anything surprising or revolutionary, but I just took a few quick readings on some mesh, same thread count, different diameter.

Coated using identical technique on Kiwo Simplex. 1-2 round
Speed 6 (Irrelevant)
Ulano Orange
Coated and dried overnight in 30% RH
Imaged with Kiwo I-Jet
Exposed on Olec 5K 65 light units
Developed with warm water pres soak and 750 PSI wash
Dried room temp (70 +/-)
measured after four hours dry time

158-48  59 EOM
156-64   24 EOM

These are all parameters used in my shop and different than yours. Just trying to show what the difference in thread diameter makes in coating a screen, and final EOM.


Dave, curious are you stating microns or perecentage of EOM.  In other words, in your 158/48 example is it 59% EOM or 59 Microns EOM?   Just clarifying the data reference for an apples to apples discussion.
Logged
Greg Kitson
Mind's Eye Graphics Inc.
260-724-2050

Offline bimmridder

  • Gonzo Member
  • ******
  • Posts: 1889
Re: Thread diameters and EOM
« Reply #5 on: April 12, 2013, 08:04:20 AM »
An oversight on my part. The EOM is microns, not a percentage (You expect me to do math?)
Logged
Barth Gimble

Printing  (not well) for 35 years. Strong in licensed sports apparel. Plastisol printer. Located in Cedar Rapids, IA

Offline mk162

  • Ludicrous Speed Member
  • *******
  • Posts: 7866
Re: Thread diameters and EOM
« Reply #6 on: April 16, 2013, 12:52:10 PM »
yeah, if the math isn't in multiples of 12, we are lost.
Logged

Offline Rockers

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2074
Re: Thread diameters and EOM
« Reply #7 on: April 16, 2013, 07:46:02 PM »
Quote from: Homer on April 11, 2013, 09:31:48 PM
stupid question but is there any other "thin thread" mesh besides murakami s mesh? I can't seem to get it locally anymore.
NBC mesh.
Logged
Pages: [1]   Go Up
« previous next »