DTF under bill of hat

[balloonguy]

Hey All.
I have a customer looking for some text under the bill of his hats (alpha tt802). Different bible verses on different colors. I have been using some supa colors transfers on these. About half the time it works fine and the other half it does not. I have tried a few temps and longer press times. Do any of you do this? Have any tips?
Thanks!

[Admiral]

Platen heating up affecting it? Too small of detail? When you say it doesn't work - what parts are failing?

Pressing too long can be an issue too.  Sometimes it overheats, shrinks the print and becomes a kind of melted mess.  We haven't experience that in a long time but if we press nylon, we need to reduce heat and time a bit for instance.

Is it all the same material? is it cotton or poly?

[Frog]

I'd like to see pics of just how it failed.
Problems I have had in the past, though few and far between were generally poor adhesion of fine lines.

[Sbrem]

The word from Supacolor as I received it was .75 point for stand alone white, 1.15 point for color, if that helps

Steve

[balloonguy]

Here are a couple pics. Some of teh text is not sticking…
 

[Frog]

Here are a couple pics. Some of teh text is not sticking…

I'm figuring the relatively unyielding hard surface along with the seams is not helping matters.

[DonR]

The seams and small text are going to be a problem.  Try using as much pressure as you can to press into the seams.  No matter what you do, it may not be 100% problem free

[balloonguy]

Thanks for the input. I will keep workin on it.

[zanegun08]

Try cold peeling, I know they say it's "Supa Easy" but often times when the transfers aren't sticking, try cold peeling and it may work better that way.  Give it some finesse and roll the transfer off once completely cold, then if you want to post press with kraft or teflon that helps adhere edges better, but don't think totally necessary on the bill of a trucker.

Sometimes the transfers don't have enough glue applied so trying it on something else or flat to make sure it works well can help check that isn't the case.

[mk162]

Try cold peeling, I know they say it's "Supa Easy" but often times when the transfers aren't sticking, try cold peeling and it may work better that way.  Give it some finesse and roll the transfer off once completely cold, then if you want to post press with kraft or teflon that helps adhere edges better, but don't think totally necessary on the bill of a trucker.

Sometimes the transfers don't have enough glue applied so trying it on something else or flat to make sure it works well can help check that isn't the case.

I find warm peeling helps.  Like 2-3 seconds or so and it's good.  I also run the time over recommended by a few seconds as well.

[ThePrinter]

I find this little guy helps out with unique locations. Might help with the text. It has 3 Temp settings, 200F, 300F, and 400F.

https://www.amazon.com/Cricut-EasyPress-Heat-Pressing-Ceramic-Coated-Lightweight/dp/B07VKPZS24/ref=sr_1_2?crid=21YGC3L1BMOTQ&dib=eyJ2IjoiMSJ9.8Kp3OmHy9upcqOOS8Viy3hhSZ1ImlOZFT2E-5XiocfGUkiv5MWCg0LTmmORlkIegUzZJj0sSZ17ADBOEAT5_RgEsmCwSzNeNtkfS2TgNuxyQp7MUii0QG3-M9gQDYPh2cWRVFJUIBIXWUUQKkYN6HK4OaaQleYpbelmBo-UuWSVVJGaTFG_LnA8v3dl9-bsurBvkiT9oIuQsnGXYShRRgxcn0NkBk7PC4AJjvAlDg3Q_-vSMB4nYoO55cSCGSNJpWT65LNRB7ugTw0KmghUSxFjMzVM1Wtotj5rSZyCNLSk.58Ft_ulSiljQKVcZfy_KrpYK74-mlxPhJWR8-pQIs4Y&dib_tag=se&keywords=cricut+iron&qid=1710259445&sprefix=cricut+iron+%2Caps%2C113&sr=8-2

[3Deep]

When we have problems with small lines sticking my wife uses a vinyl squeegee (the kind for vinyl stickers) and rub the sheet down pretty hard before she pulls off the film, that seems to help in most cases.

[Frog]

When we have problems with small lines sticking my wife uses a vinyl squeegee (the kind for vinyl stickers) and rub the sheet down pretty hard before she pulls off the film, that seems to help in most cases.

And then, a second pressing with a cover sheet, right?