Author Topic: Printing on Mesh Jersey - No open holes allowed!  (Read 2359 times)

Offline Get Shirts

  • Hero Member
  • *****
  • Posts: 649
Printing on Mesh Jersey - No open holes allowed!
« on: January 09, 2018, 11:49:07 AM »
Customer has requested the imprint on the Mesh Jersey to be a solid fill, no mesh holes "open" within the print.

We have achieved this but only by accident. What is the secret to achieving this consistently?

We do not want to transfer the image as it's 3 locations and 2k pieces.

Thanks!


Offline mimosatexas

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4221
  • contributor
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #1 on: January 09, 2018, 11:55:20 AM »
Transfers?  I kid, I kid...

Honestly, Unless you use some kind of backing below the garment that will peel away after the cure, I don't see it happening consistently.  That will also cause issues with multicolor printing unless you use a hold down.  Any time someone has asked for something like this I have used vinyl or plastisol transfers and it has been much lower quantities of course.

Offline Colin

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1610
  • Ink and Chemical Product Manager
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #2 on: January 09, 2018, 12:48:35 PM »
Really low mesh base screen (110/135 etc)

Lay down lots of ink so it fills in the holes for a solid sheet of plastisol.

Overflash/longer flash so the entire ink layer (yes even the ink that went through/into the holes gets gelled).

Calculate time wasted.

Print the rest of your colors.

Pull off of platen carefully.

Pay attention to your glue/ink residue on the platen.

Realize you still need to scrape ink off of your platens on occasion.... and reglue.

Recalculate production speeds.

Think about putting papers down under the print for easier release from your platen.

Realize at the end of the dryer that the papers will not always come off the inside of the shirt.

Spend hours picking pieces of paper out of the ink.

Think more about doing transfers....
Been in the industry since 1996.  5+ years with QCM Inks.  Been a part of shops of all sizes and abilities both as a printer and as an Artist/separator.  I am now the Ink and Chemical Product Manager at Ryonet.

Offline Chadwick

  • Sr. Member
  • ****
  • Posts: 463
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #3 on: January 09, 2018, 03:21:41 PM »
Not impossible, but really time consuming and frustrating.
Not to mention, it will not be consistent, no matter what you do.

I used to do it for tens of jerseys...with relative success.
I'd rather stick needles in my eyes than attempt to do thousands.


Offline Sbrem

  • Ludicrous Speed Member
  • *******
  • Posts: 6055
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #4 on: January 09, 2018, 04:56:14 PM »
I would just tell them it doesn't work that way. If they want to come show me how, I'll pay them, LOL!

Steve
I made a mistake once; I thought I was wrong about something; I wasn't

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #5 on: January 09, 2018, 06:21:05 PM »
It's gonna take P/F/P/F/P and it helps if you can flash again before pulling off this will REALLY help with the hole fill..FIRST SCREEN 160 TO SEAL IT UP THEN THE LAST 2 110. 65-70d range squeegies in all heads. don't over flash as they will shrink, melt etc. DO NOT use backing that's what we do to open the holes when pulled hot.  you will need to scrape the pallets on the fly every few rounds. They really are not that bad once you get rolling. scraping on the fly with the pallets hot and ink hot is a breeze. You may need to stop occasionally to let the pallets cool down.
Specializing in shop assessment's, flow and efficiency

Offline Stinkhorn Press

  • !!!
  • Hero Member
  • *****
  • Posts: 545
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #6 on: January 10, 2018, 12:55:01 PM »
It's gonna take P/F/P/F/P and it helps if you can flash again before pulling off this will REALLY help with the hole fill..FIRST SCREEN 160 TO SEAL IT UP THEN THE LAST 2 110. 65-70d range squeegies in all heads. don't over flash as they will shrink, melt etc. DO NOT use backing that's what we do to open the holes when pulled hot.  you will need to scrape the pallets on the fly every few rounds. They really are not that bad once you get rolling. scraping on the fly with the pallets hot and ink hot is a breeze. You may need to stop occasionally to let the pallets cool down.

really finesse your flash time/power ratios - don't LET the platens get too hot.
but I'm talking out my ass, we would never try to satisfy that request, more power to ya!

Offline Streetcreep

  • !!!
  • Newbie
  • *
  • Posts: 5
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #7 on: January 10, 2018, 01:57:57 PM »
Your best strategy may be to steer your customer in to a non-fully perforated jersey.  There are a bunch of options out there that have a "faux" perf, much easier to print on, leaving a nice solid imprint.  A good portion of our athletic contract customers use this style of jersey.

Offline shaneds

  • Verified/Junior
  • **
  • Posts: 47
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #8 on: January 10, 2018, 04:15:54 PM »
You can also put down foam on your boards and print direct, same sequence as your normal. We've had good success that way.


Offline 3Deep

  • !!!
  • Ludicrous Speed Member
  • *******
  • Posts: 5330
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #9 on: January 10, 2018, 04:23:37 PM »
Everything you guys suggested sounds great, but once they are washed a few times that ink will fall out of those holes, maybe not all but some.
Life is like Kool-Aid, gotta add sugar/hardwork to make it sweet!!

Offline Sbrem

  • Ludicrous Speed Member
  • *******
  • Posts: 6055
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #10 on: January 10, 2018, 04:59:37 PM »
What the heck is the point of filling in the holes? They're there to ventilate! Man, people are weird...

Steve
I made a mistake once; I thought I was wrong about something; I wasn't

Offline scrubz

  • Verified/Junior
  • **
  • Posts: 19
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #11 on: January 10, 2018, 05:14:33 PM »
Cad cut thermo film, or premium heat press transfers.  Order them from Stahls.  Even with the longer heat press time, may still be the same time as fussing with the prints.  You will probably need to charge more though....

Offline Get Shirts

  • Hero Member
  • *****
  • Posts: 649
Re: Printing on Mesh Jersey - No open holes allowed!
« Reply #12 on: January 10, 2018, 09:22:00 PM »
Great advice everyone. We’re going to quote as a transfer and see if they go for it. I can’t imagine this ever being worth our time otherwise!


Sent from my iPhone using Tapatalk