« previous next »
Pages: [1]   Go Down

Author Topic: Sleeve print hang ups  (Read 1447 times)

Offline rmonks

  • !!!
  • Sr. Member
  • ****
  • Posts: 457
Sleeve print hang ups
« on: October 28, 2015, 10:27:41 PM »
I have an Auto (M&R Gauntlet) Any suggestions how to reduce or eliminate the problem of sleeves hanging up on on the yellow levers that hold the platens in place as I am removing the shirt from the platen.
Thanks in advance
Logged

Offline LuckyFlyinROUSH

  • !!!
  • Sr. Member
  • ****
  • Posts: 334
Re: Sleeve print hang ups
« Reply #1 on: October 28, 2015, 10:47:37 PM »
Trick we have figured out is to grab the collar and side of the shirt...and yank...HARD straight off. Don't even bother touching the other side of the sleeve. Seems like they pop off pretty easy that way. Make sure you flash first if possible to prevent flips.
Logged
I spend too much money on equipment...

Offline Colin

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1610
  • Ink and Chemical Product Manager
Re: Sleeve print hang ups
« Reply #2 on: October 28, 2015, 11:15:50 PM »
Throw a strip of tape over them.

You want to essentially create a cover over the clamps.  Everything will just slide right off.
Logged
Been in the industry since 1996.  5+ years with QCM Inks.  Been a part of shops of all sizes and abilities both as a printer and as an Artist/separator.  I am now the Ink and Chemical Product Manager at Ryonet.

Offline Screen Dan

  • !!!
  • Full Member
  • ***
  • Posts: 209
Re: Sleeve print hang ups
« Reply #3 on: October 29, 2015, 07:51:37 AM »
I dunno.  I always found that the perfect amount of spray tack and a good firm yank on the cuff, perfectly straight out, usually got them off with no problems.  Smalls and hoodies can be a pain...but never so much that I felt a need to do anything about it.

Pop it straight outward with no bias for pulling up or down.  Too much tack and this pretty much won't work, you'll be peeling up and subject to the whims of the levers.
Logged

Offline 244

  • Gonzo Member
  • ******
  • Posts: 1368
Re: Sleeve print hang ups
« Reply #4 on: October 29, 2015, 08:19:12 AM »
Quote from: rmonks on October 28, 2015, 10:27:41 PM
I have an Auto (M&R Gauntlet) Any suggestions how to reduce or eliminate the problem of sleeves hanging up on on the yellow levers that hold the platens in place as I am removing the shirt from the platen.
Thanks in advance
adjust the levers so when tight they are parallel with the arm and there is nothing to hang up on.
Logged
Rich Hoffman

Offline Ross_S

  • Sr. Member
  • ****
  • Posts: 349
Re: Sleeve print hang ups
« Reply #5 on: October 29, 2015, 08:41:16 AM »
Besides what Rich said we tape put tape around the handles and tape to the arm (Long Runs of course).  That way when you go to unload the handle can't grab the garment.
Logged

Offline tonypep

  • Ludicrous Speed Member
  • *******
  • Posts: 5681
Re: Sleeve print hang ups
« Reply #6 on: October 29, 2015, 08:41:32 AM »
Tape works but of course Rich is right. Two half inch wrenches (one shd be a socket) and you can make quick work of it. Well that's what we use on our dinosaurs.
Logged

Offline mimosatexas

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4221
  • contributor
Re: Sleeve print hang ups
« Reply #7 on: October 29, 2015, 09:17:18 AM »
I do what rich said. Adjust it so the levers areally parallel to the pallet arm. Never had hang up issues. Tape sounds like even more insurance against hang ups.
Logged

Offline Ross_S

  • Sr. Member
  • ****
  • Posts: 349
Re: Sleeve print hang ups
« Reply #8 on: October 29, 2015, 09:19:08 AM »
THe tape helps for smaller sizes god forbid you have youths.
Logged
Pages: [1]   Go Up
« previous next »