Author Topic: Exposure decision advice  (Read 4594 times)

Offline ABuffington

  • Hero Member
  • *****
  • Posts: 545
Re: Exposure decision advice
« Reply #30 on: November 04, 2014, 04:41:41 PM »
Hello Pierre,

It was great to see you and other forum members at the show. 

About overexposure.

Here is one way to look at it.

With a 50-100x microscope we examine a 40-50% halftone.  We look specifically at the side wall of the halftone to see if there is a dark halo, or a light halo around the dot, or whatever dot shape you use, and we view the dot from the print side of the screen.  A light halo inside the halftone dot shows overexposure.  The dot has been undercut with too much light and the emulsion opening on the squeegee side is smaller than the print side.  The sidewall is angling inward to create the smaller halftone opening on the squeegee side.  With a dark circle the opening on the squeegee side is wider due to the developing water washing away soft emulsion and we are seeing the shadow and emulsion when viewing from the print side.  The more the halftone dot shape has no dark or light halos around them the more vertical the halftone sidewall.  A halftone like this will not dot gain as easily (underexposure) or require more pressure to clear <20% dots, (overexposure).  Helps keep sim process sharp and tonal values accurate, although some dot gain is to be expected, thats why halftone outputs to film should be linearized to compensate for dot gain of 10-20%

This all assumes you have a well functioning lamp.  If your lamp is old you can both overexpose and underexpose a screen, huh?  OK I did have band practice last night but I've sobered up by now, so this can happen.  What is going on is the exposure time in light units may be long due to a weak MH lamp or if you use weak chaotic fluorescent lamps.  The time needed to get the emulsion film exposed to avoid slime on the inside may be so long that undercutting is occuring, and an older lamp's light may have lost UV power and is not cross linking the emulsion completely.  Typically discharge or HSA inks will cause premature breakdown on what was supposed to be adequate or more than adequate time.  The strength of the light in the 360-420 nanometer wavelengths is key.  If the bulb has aged it may still shoot a screen well for plastisol, but for discharge it can breakdown in hundreds of prints once the lamp has lost strength.  So yes you can over expose and under expose on the same screen but it just won't be visible until it breaks down.

However there are times where overexposing can help simple spot art for discharge.  Bumping exposure 10-20% isn't going to hurt solid spot art and will give it a little more durability when shot with a fresh MH, or LED. 

Al
Alan Buffington
Murakami Screen USA  - Technical Support and Sales
www.murakamiscreen.com


Offline mimosatexas

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4221
  • contributor
Re: Exposure decision advice
« Reply #31 on: November 04, 2014, 05:00:17 PM »
I got a phone call while exposing a 2/1 coated SP-1400 on 280 yellow mesh yesterday and ended up exposing it for almost 12 minutes, which is about 3 times as long as my standard exposure for that mesh/emulsion on my current unit.  It washed out more or less perfectly which shocked the hell out of me.  No halftones though so a little undercutting isn't a big deal.

Offline Extreme Screen Prints

  • Verified/Junior
  • **
  • Posts: 56
Re: Exposure decision advice
« Reply #32 on: November 06, 2014, 02:25:04 PM »
We purchased a starlight a few months back and it has been great, Very comparable to detail of Metal Halide, I Wish the starlight was 3 inches wider so I could shoot 2 screen at a time, To me it doesn't make sense why M&R did not just make the frame 3 inches bigger but leave the LED strips the same size. Might add $500 in material but we would be able to shoot 2 screens at a time. I have a feeling this will be something they come out with in the next year and we will all upgrade. LOL

Offline Admiral

  • Hero Member
  • *****
  • Posts: 892
Re: Exposure decision advice
« Reply #33 on: November 06, 2014, 04:03:07 PM »
We purchased a starlight a few months back and it has been great, Very comparable to detail of Metal Halide, I Wish the starlight was 3 inches wider so I could shoot 2 screen at a time, To me it doesn't make sense why M&R did not just make the frame 3 inches bigger but leave the LED strips the same size. Might add $500 in material but we would be able to shoot 2 screens at a time. I have a feeling this will be something they come out with in the next year and we will all upgrade. LOL

Most of the benefit is lost though with such fast exposure times.  Our pure photo-polymer emulsion is done exposing before you can walk out of the door of the dark room that is only 6 feet away...

With diazo I suppose it might almost be worth it but those times are still pretty low for us.  Work flow wise it doesn't help though too because you grab the imaged screen, load new screen to be imaged, expose screen you took off CTS....etc, the imaging and washing out are the slower parts now...