A Quick slide show on how to use Pallet Paper

[Prōdigium]

Its seems so obvious to the shops who use pallet paper everyday, but for someone who is new to the printing business you may not realize how a simple product like this can save not only countless hours every week, but also extend the life of your pallets and remove any need for stinky, hazardous cleaning solvents at the same time.

What I am talking about is a product called Pallet Paper...available by clicking here, and all it simply does is cover your printing pallets with a protective layer of adhesive backed paper for your to apply your spray tack to, when its dirty you simply replace it as shown.

Dirty Pallet



Remove Old Paper



Place Down New Layer



Trim Edges With X-acto Blade.



Place Tape On front Edge To Hold When Loading



Fresh New Pallet In No Time At All!!

[Evo]

Secret weapon for smooth pallet tape:


THE BRAYER!


Picked up a couple of these from Goodwill for a dollar. You can find them at art supply stores.

Excellent for quickly and thoroughly smoothing down pallet tape, (get the bubbles out!)

Also works great for burnishing mesh protection tape on new frames.

[Prōdigium]

I have never needed the use of any tools to apply a smooth layer of pallet paper....that being said I have also used pallet paper in my printing days for well over 15 years and have simply got so good at it that I can change the paper on an 8-color automatic in about 10 minutes or less.

But if the tool works for ya , have at it. I have found that any small air pockets are usually squelched out on the first few test prints..at least on an automatic press. It still amazes me to this day that people refuse to use pallet paper and think its too expensive, or time consuming. Some basic math and a reasonable value of your "time" would clearly prove pallet paper to be a no brainer.....another big PLUS if you are prone to scorching pallets under the flash dryer is that the paper will smell bad BEFORE you do much damage to your pallet. 

[bimmridder]

And yet another opinion (nice to see you by the way Lance) We use a putty knife, but other things would work. We simply draw a few inches off the back edge of the platen, burnish it down with hand or putty knife. Pull the roll towards you until an inch or so is beyond the platen. A quick swipe with the putty knife to cut the paper (nice and straight). Take the roll of paper and set it on the back of the platen where the paper was rubbed down. Draw the roll over the platen to smooth it out and adhere it.  Wrap the edges under the platen. No cutting or taping. This is a slight variation from what we used to do, but picked up from a friend. Two people on an 16 color press takes about 4 minutes to apply. (peeling the old crap is another story!)

[Prōdigium]

Two people on an 16 color press takes about 4 minutes to apply. (peeling the old crap is another story!)

A simple trick to solve that problem is to lay down a "permanent" base layer of pallet paper on your pallets with the edges taped nice and cleanly. Draw your center lines or any other patterns you like on that layer. Then apply your 'production' pallet paper on top. When you go to change your paper, you will notice a HUGE difference in how easy it is to remove and if you use center lines as I do, you will never have to redraw them on your pallets again. 

[bimmridder]

Correct, Lance. Laying multiple layers is the way to go, but when you decide to take the very first piece off, it takes a lot longer. Don't use any markings here though. Thanks for mentioning what was routine to me.

[screenxpress]

And yet another opinion (nice to see you by the way Lance) We use a putty knife, but other things would work. We simply draw a few inches off the back edge of the platen, burnish it down with hand or putty knife. Pull the roll towards you until an inch or so is beyond the platen. A quick swipe with the pussy knife to cut the paper (nice and straight). Take the roll of paper and set it on the back of the platen where the paper was rubbed down. Draw the roll over the platen to smooth it out and adhere it.  Wrap the edges under the platen. No cutting or taping. This is a slight variation from what we used to do, but picked up from a friend. Two people on an 16 color press takes about 4 minutes to apply. (peeling the old crap is another story!)

I am not even going to ask about this.

[Frog]

Man, a set-up like that is like pu**y in your hands, eh?

[Evo]

Gotta say, that is a great name for an all-girl punk band.

[Mr Tees!!]

hey Evo, wasnt that your nickname in highschool??...