« previous next »
Pages: [1]   Go Down

Author Topic: Poly Drawstring Back Pak 7/5  (Read 2013 times)

Offline DCSP John

  • Sr. Member
  • ****
  • Posts: 340
Poly Drawstring Back Pak 7/5
« on: July 05, 2018, 01:33:31 PM »
I have never had a print run of poly back packs.
But - I have 100 here that I need to print. Pink w/ black ink.

Any suggestions on ink? Low temp additive or a specialty ink?

Thanks.  - John
Logged

Offline im_mcguire

  • !!!
  • Hero Member
  • *****
  • Posts: 716
Re: Poly Drawstring Back Pak 7/5
« Reply #1 on: July 05, 2018, 02:11:47 PM »
Id look into One Strokes low cure ink
Logged

Offline nicolas

  • Verified/Junior
  • **
  • Posts: 32
Re: Poly Drawstring Back Pak 7/5
« Reply #2 on: August 30, 2018, 03:01:08 AM »
Quote from: Adriennei on August 30, 2018, 01:01:00 AM
What is the source of most of the information that comes from this forum?

The Internetses
Logged

Offline balloonguy

  • !!!
  • Hero Member
  • *****
  • Posts: 985
Re: Poly Drawstring Back Pak 7/5
« Reply #3 on: August 30, 2018, 08:39:26 AM »
with black ink you could use an air dry ink like 7200 from nazdar or anything for coroplast. Adding a catalyst will ensure full cure in 20 minutes or so. It can be a pain to work with though. I prefer to just attach a couple of blow dryers on the open print heads...
Logged
When you dig grave will you make it shallow so that I can feel the rain?

Offline Doug B

  • !!!
  • Hero Member
  • *****
  • Posts: 547
Re: Poly Drawstring Back Pak 7/5
« Reply #4 on: August 30, 2018, 12:26:54 PM »
  Although NazDar 7200 says it is flexible, It will harden and crack when fully cured. I
would just add some Nylobond to plastisol for black ink. Being black on polyester you won't
have to worry about bleeding and the Nylobond will reduce the cure temperature.
Logged

Offline whitewater

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1831
Re: Poly Drawstring Back Pak 7/5
« Reply #5 on: August 30, 2018, 01:06:51 PM »
we use the nylobond.
Logged

Offline Frog

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 13980
  • Docendo discimus
Re: Poly Drawstring Back Pak 7/5
« Reply #6 on: August 30, 2018, 01:17:24 PM »
do you find that Nylobond stiffens the ink at all? I remember years ago seeing a job that had gotten quite brittle. Perhaps it was way over cured, (or mixed in a bad proportion) I don't know.
Logged
That rug really tied the room together, did it not?

Offline im_mcguire

  • !!!
  • Hero Member
  • *****
  • Posts: 716
Re: Poly Drawstring Back Pak 7/5
« Reply #7 on: August 30, 2018, 01:28:28 PM »
Quote from: Frog on August 30, 2018, 01:17:24 PM
do you find that Nylobond stiffens the ink at all? I remember years ago seeing a job that had gotten quite brittle. Perhaps it was way over cured, (or mixed in a bad proportion) I don't know.
Im running a job right now with Nylobond, and it does great.  Using regular plastisol with 7.5% nylobond.  It thins out our ink a little, but the opacity is still bright on a navy bag and 1 stroke through a 1150 s mesh.
Logged

Offline Maxie

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1328
Re: Poly Drawstring Back Pak 7/5
« Reply #8 on: August 30, 2018, 01:42:37 PM »
I’m sure not all bags are the same.
We use nylobond and also drop the temp to 250 F to stop the cords shrinking because of the heat.
It’s not perfect, you can still scratch the ink off with your fingernail but it’s the best we can get.
I don’t think anybody washes these things, problem mainly is with rubbing.
Logged
Maxie Garb.
T Max Designs.
Silk Screen Printers
www.tmax.co.il

Offline whitewater

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1831
Re: Poly Drawstring Back Pak 7/5
« Reply #9 on: August 30, 2018, 06:50:11 PM »
Quote from: Frog on August 30, 2018, 01:17:24 PM
do you find that Nylobond stiffens the ink at all? I remember years ago seeing a job that had gotten quite brittle. Perhaps it was way over cured, (or mixed in a bad proportion) I don't know.

when printing the ink its stiff.
Logged
Pages: [1]   Go Up
« previous next »