Author Topic: which ink should I use?  (Read 2351 times)

Offline Shanarchy

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1421
which ink should I use?
« on: November 21, 2011, 10:06:55 AM »
I am going to be printing on Hanes 4820 100% poly shirts in the color graphite.  https://www.nesclothing.com/cgi-bin/online/webshr/prod-detail.w?sr=4820&currentColor=43. I will be printing 2 colors, black and red. I have some low bleed red on the shelf. Will I be fine with that or should I order in some poly red?

Thanks in advance!


Offline mk162

  • Ludicrous Speed Member
  • *******
  • Posts: 7857
Re: which ink should I use?
« Reply #1 on: November 21, 2011, 10:13:49 AM »
low bleed red should be fine, just watch your temps and I would recommend a test that you can wash and let sit until tomorrow.

Graphite shouldn't be a huge bleeding color.

Offline Sbrem

  • Ludicrous Speed Member
  • *******
  • Posts: 6055
Re: which ink should I use?
« Reply #2 on: November 21, 2011, 11:49:44 AM »
If you have the low bleed red, use it, but test first of course. I don't think you'll have any trouble with the black, we've printed regular black on a few thousand of those without incident.

Steve
I made a mistake once; I thought I was wrong about something; I wasn't

Offline Fluid

  • !!!
  • Sr. Member
  • ****
  • Posts: 462
  • Keep the Ink Moving... Stay Corelian My Friends!
Re: which ink should I use?
« Reply #3 on: November 21, 2011, 03:28:26 PM »
Depending on how dark the graphite T is the only Issue I really see is it darkening your red just like any colored shirt would without the use of a white underbase. As mentioned, test, test, test before running the entire order.  Getting that extra shirt isn't that big of a cost and you can always use that shirt for other test prints or give to your client as an extra over run.

« Last Edit: November 21, 2011, 03:51:29 PM by Fluid »
Richard
--Fluid       www.fluiddsn.com Graphic Designs, Color Separations & Film Output 15+ years Industry Experience - CorelDRAW MasterĀ® 

Offline ebscreen

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4278
Re: which ink should I use?
« Reply #4 on: November 21, 2011, 03:33:55 PM »
Black, low-bleed white underbase, flash, red, done.

Offline Fluid

  • !!!
  • Sr. Member
  • ****
  • Posts: 462
  • Keep the Ink Moving... Stay Corelian My Friends!
Re: which ink should I use?
« Reply #5 on: November 21, 2011, 03:52:23 PM »
Black, low-bleed white underbase, flash, red, done.

or a Poly White - unfortunately the cost for Poly white is a lot higher yet the outcome is well worth it.


Richard
--Fluid       www.fluiddsn.com Graphic Designs, Color Separations & Film Output 15+ years Industry Experience - CorelDRAW MasterĀ® 

Offline ebscreen

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4278
Re: which ink should I use?
« Reply #6 on: November 21, 2011, 04:01:55 PM »
Here, poly and low bleed are the same. If our regular cotton white (which works on some blends) is not
suitable for the job, then the poly is what is used. No middle ground with potential bleeders.


Offline DanK

  • Full Member
  • ***
  • Posts: 113
Re: which ink should I use?
« Reply #7 on: November 21, 2011, 04:44:57 PM »
We've been using this Rutland Endurance product for the past month, and it's been awesome.  Datasheet is attached.
Dan Holzer

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: which ink should I use?
« Reply #8 on: November 21, 2011, 07:31:17 PM »
graphite in that style are not bad bleeders.. you will be ok with a standard low bleed underbase under the red and a standard black.
Specializing in shop assessment's, flow and efficiency