« previous next »
Pages: [1]   Go Down

Author Topic: printing aprons (how do you do it)  (Read 1508 times)

Offline Screened Gear

  • Gonzo Member
  • ******
  • Posts: 2580
printing aprons (how do you do it)
« on: March 23, 2012, 04:48:08 PM »
ok I have a 500 order of aprons. Never printed this many on an auto.  Do I print them upside down like a bag or normal. Should I set up lasers for placement? how do you deal with the straps and over hanging material? How do you guys do it.
Logged

Offline Homer

  • !!!
  • Gonzo Member
  • ******
  • Posts: 3205
Re: printing aprons (how do you do it)
« Reply #1 on: March 23, 2012, 04:53:06 PM »
sometimes we put the image on each platen so we know where it's going to hit . We print the screen on fresh platen tape, then put the glue on. It helps with things with close edges, like the top part of an apron.  . .put the apron on neck first, if the design is high up on the chest. goes pretty quick, faster than t-shirts if you set up right.
Logged
...keep doing what you're doing, you'll only get what you've got...

Offline Socalfmf

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1238
  • Lead, Follow or Get Out of the Way!
Re: printing aprons (how do you do it)
« Reply #2 on: March 23, 2012, 04:53:33 PM »
we do them upside down like a bag and move the boards out so we align the top to the bottom of the pallet for easy placement.  works like a charm..plus we use the lazer for center...
Logged

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: printing aprons (how do you do it)
« Reply #3 on: March 24, 2012, 07:45:10 PM »
we run those babys the same way sam..
Logged
Specializing in shop assessment's, flow and efficiency

Offline mooseman

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2215
Re: printing aprons (how do you do it)
« Reply #4 on: April 14, 2012, 08:44:56 AM »
On our manual...
we have a sheet of paneling / white board we got at lowes / home depot 4 x8 standard size.
 it is 1/8 thick with typical white board on one side press board finish on the back. we stack cut 6 of them to match the pattern of the typical apron.
coat both sides with a good coating of water based adhesive Tekbond stuff and simply stick them onto our standard pallets and then simply fit the aprons onto the patterned pallets.
This makes the loading quick and easy and drops all the apron seams etc below screen contact.
After the job pull up the templates and save for the next job.
moosenman
Logged
DUE TO CIRCUMSTANCES COMPLETELY WITHIN MY CONTROL YOU SHOULD GET YOUR OWN TEE SHIRT AND A SHARPIE MARKER BY NOON TOMORROW OR SIMPLY CALL SOMEONE WHO GIVES A SHIRT.

Offline Gabe

  • Sr. Member
  • ****
  • Posts: 483
  • If it`s not alive, I can print it.
Re: printing aprons (how do you do it)
« Reply #5 on: April 14, 2012, 09:10:18 AM »
Quote from: mooseman on April 14, 2012, 08:44:56 AM
On our manual...
we have a sheet of paneling / white board we got at lowes / home depot 4 x8 standard size.
 it is 1/8 thick with typical white board on one side press board finish on the back. we stack cut 6 of them to match the pattern of the typical apron.
coat both sides with a good coating of water based adhesive Tekbond stuff and simply stick them onto our standard pallets and then simply fit the aprons onto the patterned pallets.
This makes the loading quick and easy and drops all the apron seams etc below screen contact.
After the job pull up the templates and save for the next job.
moosenman
did it once like you did moose man with the panels instead of water base glue i used
the pallet tape with the glue already on it worked great on aprons knock out 1000 of them nice and easy
Logged
Pages: [1]   Go Up
« previous next »