« previous next »
Pages: [1]   Go Down

Author Topic: S-Mesh Count for Metallics  (Read 1435 times)

Offline sqslabs

  • Hero Member
  • *****
  • Posts: 972
  • Work hardened.
S-Mesh Count for Metallics
« on: May 07, 2015, 12:32:00 PM »
We usually run our metallic inks through 90 mesh statics, but now that we have our pin system running at full speed I'd like to get some mesh on rollers for that purpose.  Anybody using S-Mesh for metallics, and if so what count are you using?

Thank youuuuuu.
Logged
Brett
Squeegee Science
Fort Lauderdale, FL

Offline blue moon

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 6366
Re: S-Mesh Count for Metallics
« Reply #1 on: May 07, 2015, 12:40:36 PM »
83 LX baby!!!

Holly crap the size of the openings!

pierre
Logged
Yes, we've won our share of awards, and yes, I've tested stuff and read the scientific papers, but ultimately take everything I say with more than just a grain of salt! So if you are looking for trouble, just do as I say or even better, do something I said years ago!

Offline Colin

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1610
  • Ink and Chemical Product Manager
Re: S-Mesh Count for Metallics
« Reply #2 on: May 07, 2015, 02:37:21 PM »
Like Pierre said:  S Thread or LX Thread will do the trick.  You find the mesh count that you enjoy best.

I know shops that go up to 150 LX for metallics.  I would probably stay at 135 or lower myself.
Logged
Been in the industry since 1996.  5+ years with QCM Inks.  Been a part of shops of all sizes and abilities both as a printer and as an Artist/separator.  I am now the Ink and Chemical Product Manager at Ryonet.

Offline brandon

  • Gonzo Member
  • ******
  • Posts: 1709
Re: S-Mesh Count for Metallics
« Reply #3 on: May 07, 2015, 02:39:33 PM »
Yup, all great advice. And water base metallics rule the day  :)
Logged

Offline ZooCity

  • Gonzo Member
  • ******
  • Posts: 4914
Re: S-Mesh Count for Metallics
« Reply #4 on: May 07, 2015, 03:31:02 PM »
What type of metallic? 

For us:

WFX Shimmers 90/71
WFX Liquids can run up to 150/48 or even higher, depending on the desired look.

Brandon loves the Matsui metallic but we had a pretty rough time with the couple gallons we tried.  It seems likely they were off batches though.  My choice to continue with plastisol metallics was based off the fact that the finished print felt about the same between the two so we stick with the reliable plastis.  The WFX Liquids give a finish I haven't seen from any other ink system and have been the go-to here for a few years. 

Pierre that 80/55 is crazy open.  I think we have a panel of it here that we never used as the 90/71 gets it done without being crazy delicate.  I think the 80/55 is actually an "SS" mesh.
Logged

Online Rockers

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2073
Re: S-Mesh Count for Metallics
« Reply #5 on: May 07, 2015, 05:05:29 PM »
We have done Wilflex liquid silver on 180-48 and 225-48 and as low as 150-48.
For other brands metallics, like Union I would stick with anything from 120-150-S mesh.
Logged
Pages: [1]   Go Up
« previous next »