Author Topic: Epic Curable Reducer or Finesse?  (Read 1448 times)

Offline jvanick

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2477
Epic Curable Reducer or Finesse?
« on: August 08, 2013, 11:33:42 AM »
now that I'm starting to print a lot more jobs on the auto, I seem to need to thin my inks a bit... trying to figure out which of the following I should be using:

I typically print with Wilflex inks, so...

which is my better choice to get a softer hand and better printability Epic Finesse or just the standard Epic Curable reducer...

I could buy a gallon of each, but if somebody else as already gone through this exercise, would be cool to hear the opinions...

Thanks!
-J


Offline Zelko-4-EVA

  • Hero Member
  • *****
  • Posts: 573
Re: Epic Curable Reducer or Finesse?
« Reply #1 on: August 08, 2013, 11:44:39 AM »
we are using the PC system on our autos (and manual) and are not thinned unless the customer specifies it.

when we thin our inks we use SHC10140 Soft Hand Clear.

Offline dirkdiggler

  • Gonzo Member
  • ******
  • Posts: 1803
Re: Epic Curable Reducer or Finesse?
« Reply #2 on: August 08, 2013, 02:07:14 PM »
all of those will work.  I think Finesse is cheapest, so I would do that.  That's what I do.  WHen needed, but honestly, its rarely needed in wilflex inks.  I only do it to extend my bucket.
If he gets up, we'll all get up, IT'LL BE ANARCHY!-John Bender

Offline GaryG

  • !!!
  • Hero Member
  • *****
  • Posts: 750
Re: Epic Curable Reducer or Finesse?
« Reply #3 on: August 08, 2013, 02:21:14 PM »
Yeah mostly Wilflex here too, and recently went to Curable Reducer for the most part.
Finesse is thicker and used more to -extend (eg: make black go longer 10-30% and higher) than reduce.
Curable reducer 5-10% as specified to thin.

Offline jvanick

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2477
Re: Epic Curable Reducer or Finesse?
« Reply #4 on: August 08, 2013, 02:52:51 PM »
so I'm just getting started on the auto and it was a wierd problem for us:

I was having problems with Epic black on the auto, like it was too thick or something, it wouldn't clear the screen... we had a quart of IC's black and a bit of IC's curable reducer, printed just fine on the auto, same setup, pressure, angle, everything... all I did was clear the epic out, and put the ic in, and problems went away.

epic white prints out of the bucket, no problems at all...  go figure.

-J


Offline dirkdiggler

  • Gonzo Member
  • ******
  • Posts: 1803
Re: Epic Curable Reducer or Finesse?
« Reply #5 on: August 08, 2013, 03:00:28 PM »
epic matte black out of the bucket is the dogs bollucks!  if you are having trouble with it, you shouldn't.  send it back or check your procedure.
If he gets up, we'll all get up, IT'LL BE ANARCHY!-John Bender

Offline ZooCity

  • Gonzo Member
  • ******
  • Posts: 4914
Re: Epic Curable Reducer or Finesse?
« Reply #6 on: August 08, 2013, 03:30:21 PM »
epic matte black out of the bucket is the dogs bollucks!  if you are having trouble with it, you shouldn't.  send it back or check your procedure.

Indeed.  Never a single modification needed with that ink.  It's the nuts.  Sounds like your bucket might've gotten partially cured in transit?  Try stirring.

Offline JBLUE

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2036
Re: Epic Curable Reducer or Finesse?
« Reply #7 on: August 08, 2013, 03:58:30 PM »
He does have a Javelin. Not meant as a knock at all on the press but you do have to do things a little different when running the V squeegee. I cut my teeth on a Jav and when I went to my M&R it was a learning curve in the opposite direction. The best thing to do is get setup with some triple duro squeegees. It will make a world of difference on that machine.
www.inkwerksspd.com

We are all born ignorant, but one must work hard to remain stupid...... Ben Franklin