« previous next »
Pages: [1]   Go Down

Author Topic: Does activator eat shirts?  (Read 1324 times)

Offline Screened Gear

  • Gonzo Member
  • ******
  • Posts: 2580
Does activator eat shirts?
« on: March 13, 2013, 03:23:36 PM »
I lost another shirt this week. Have about 8 holes in the front of the shirt. First does activator powder eat holes in shirts? Teh only reason I ask is because I have been working on my pool lately too. Second how do you keep from this happening. I am looking into a flip top bottle to put the powder into. I think my problem is taking the lid off of the quart container I keep in the mixing area. When I take the lid off any powder from the lid always goes flying.

Thanks in advance
Holey in Arizona
Logged

Offline Screened Gear

  • Gonzo Member
  • ******
  • Posts: 2580
Re: Does activator eat shirts?
« Reply #1 on: March 13, 2013, 05:18:16 PM »
no one else has this happen. If you get activator powder on your shirt does it eat the shirt after you wash it.
Logged

Offline ebscreen

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4281
Re: Does activator eat shirts?
« Reply #2 on: March 13, 2013, 05:33:49 PM »
I'd wager it's the pool chems.
Logged

Offline Screened Gear

  • Gonzo Member
  • ******
  • Posts: 2580
Re: Does activator eat shirts?
« Reply #3 on: March 13, 2013, 05:40:29 PM »
Im going to do a test.
Logged

Offline ebscreen

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4281
Re: Does activator eat shirts?
« Reply #4 on: March 13, 2013, 05:44:57 PM »
Science is totally rad.
Logged

Offline Screened Gear

  • Gonzo Member
  • ******
  • Posts: 2580
Re: Does activator eat shirts?
« Reply #5 on: March 13, 2013, 05:50:37 PM »
well a quick test. Straight powder sprayed with water and then dried with a heat gun made the shirt in that area weak. I could easily rip it in that area. The powder did DC the area when heated with the heat gun. My shirt is not DC around the holes. I will let it sit on the fabric and dry normally and see if it still make the fabric weak with out DCing the area. (no heat gun).
Logged

Offline ebscreen

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4281
Re: Does activator eat shirts?
« Reply #6 on: March 13, 2013, 06:21:20 PM »
Yeah, heat gun may be a factor. When we first started testing colors with it I was surprised at how easy it was
to scorch if not burn fabric.
Logged

Offline Prof_Yaffel

  • Verified/Junior
  • **
  • Posts: 14
Re: Does activator eat shirts?
« Reply #7 on: March 14, 2013, 11:27:51 AM »
Chlorine/bleach will do that if you were using it with your pool
Logged

Offline Screened Gear

  • Gonzo Member
  • ******
  • Posts: 2580
Re: Does activator eat shirts?
« Reply #8 on: March 14, 2013, 01:05:16 PM »
Ok second test did nothing. I did a scoop of powder then sprayed it with water and let it sit all night. To day the fabric is as strong as normal.
Logged

Offline blue moon

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 6366
Re: Does activator eat shirts?
« Reply #9 on: March 14, 2013, 01:09:50 PM »
we had a shirt we used for testing that was printed over and over again in the same place than sent through a very hot dryer (400+).
it started falling apart in the areas where we laid down a lot of ink.

so there is something to this story . . .

pierre
Logged
Yes, we've won our share of awards, and yes, I've tested stuff and read the scientific papers, but ultimately take everything I say with more than just a grain of salt! So if you are looking for trouble, just do as I say or even better, do something I said years ago!

Offline ZooCity

  • Gonzo Member
  • ******
  • Posts: 4914
Re: Does activator eat shirts?
« Reply #10 on: March 14, 2013, 06:29:08 PM »
Well, ZFS is def doing a chemical bleaching action. Makes sense that too much would break down fibers. Perhaps this is, in part, where the recommended six percent limit comes from.
Logged
Pages: [1]   Go Up
« previous next »