Classified Ads > Commercial listings

M&R Blue Max stretcher

<< < (2/3) > >>

mk162:

--- Quote from: Atownsend on August 07, 2024, 04:51:06 PM ---that sucks!!

We would have totally taken the MD8  :(

Its gotta be better than our Precision. I just spent a weekend swapping the blower motor bearings... Had to shim it because the previous one was totally blown out and the shaft had some wear. What a freaking PIA. Looking for a newer Sprint 2000, or 3000 come winter but the MD8 i'd run if its a little better insulated. Main goal is to improve the working conditions here. The precision gives off a lot of effing heat. Cures a ton of shirts and it never slow but damn it s hot in July / Aug.

--- End quote ---

Talk to winston about gas ovens.  He knows his stuff. (904) 343-0848  He'll steer you in the right direction for sure.

Evo:

--- Quote from: Atownsend on August 07, 2024, 04:51:06 PM ---Had to shim it because the previous one was totally blown out and the shaft had some wear. What a freaking PIA.

--- End quote ---

Hate to break it to you but a Sprint 3000 is also a PITA to swap bearings. If the shaft is damaged or worn or gouged up it should probably be swapped put at the same time as the bearing set, then professionally balanced. It makes a huge difference in noise, vibration and bearing life.

Sprints are not hot to the touch so you don't really get much radiant heat off the chassis but they blow out a TON of heat from each end. Nature of the beast.

mk162:

--- Quote from: Evo on August 09, 2024, 08:25:58 PM ---
--- Quote from: Atownsend on August 07, 2024, 04:51:06 PM ---Had to shim it because the previous one was totally blown out and the shaft had some wear. What a freaking PIA.

--- End quote ---

Hate to break it to you but a Sprint 3000 is also a PITA to swap bearings. If the shaft is damaged or worn or gouged up it should probably be swapped put at the same time as the bearing set, then professionally balanced. It makes a huge difference in noise, vibration and bearing life.

Sprints are not hot to the touch so you don't really get much radiant heat off the chassis but they blow out a TON of heat from each end. Nature of the beast.

--- End quote ---

I've heard the same about the 3000s and bearing. i also heard it chews them up, but htat could be a balancing issue.

Atownsend:

--- Quote from: mk162 on August 12, 2024, 08:41:54 AM ---
--- Quote from: Evo on August 09, 2024, 08:25:58 PM ---
--- Quote from: Atownsend on August 07, 2024, 04:51:06 PM ---Had to shim it because the previous one was totally blown out and the shaft had some wear. What a freaking PIA.

--- End quote ---

Hate to break it to you but a Sprint 3000 is also a PITA to swap bearings. If the shaft is damaged or worn or gouged up it should probably be swapped put at the same time as the bearing set, then professionally balanced. It makes a huge difference in noise, vibration and bearing life.

Sprints are not hot to the touch so you don't really get much radiant heat off the chassis but they blow out a TON of heat from each end. Nature of the beast.

--- End quote ---

I've heard the same about the 3000s and bearing. i also heard it chews them up, but htat could be a balancing issue.

--- End quote ---
That sucks!! I actually love the simplicity of the precision. I can replace almost any part on it and its reliable (for the most part). I mean... the motor is right there, belt drive it really doesn't get any easier. The insulation just blows. I talked to Winston for a bit last week. He said the 2000's also tend to rust out for one reason or another which seems a little crazy. The dryer is the heart of the shop, and not something we switch up every day. Sometimes it seems better to stick with what you know than what you dont know.

I'd love to find a HVAC company worth a crap who could fabricate a hood for the outfeed, but it seems like everyone around here just wants to drop in new units and do compressor swaps when they're not ripping off homeowners. There doesn't seem to be much any interest in doing oddball fabrication at a screen print shop.

Sbrem:
Maybe a sheet metal shop? If there is still such a thing. Decades ago we had one that made 3 separate custom screen room sinks. How about talking to the HVAC part of a local trade school? Even some of the kids would be interested maybe?

Steve

Navigation

[0] Message Index

[#] Next page

[*] Previous page