Author Topic: Silicone printing and curing  (Read 2796 times)

Offline Maxie

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1328
Silicone printing and curing
« on: March 19, 2016, 08:24:31 AM »
I am really keep to  print with silicone, we get a lot of synthetic fleece that is a nightmare to print.
I watched a clip on UTube, they printed with Dow Corning inks and cured at 150C for one min,  we cure plastisol at 160C for 2 min.     The Rutland site mentions a much lower temperature, this is a big problem for us because we are running 2 carousels through one oven and it's a real PITA to change the temperature.
Does anyone have any experience with this?     Can you cure Silicone hotter for less time?
Maxie Garb.
T Max Designs.
Silk Screen Printers
www.tmax.co.il


Offline Ross_S

  • Sr. Member
  • ****
  • Posts: 349
Re: Silicone printing and curing
« Reply #1 on: March 19, 2016, 09:36:46 AM »
Maxie;

Call Nazdar talk with Rob Coleman if he doesn't end up chiming in here.  Anyways Dow Corning is associated with Nazdar silicone.  It is best when curing at lower temps (Hand feel).  You can run it at a higher temp but it won't feel as soft but it doesn't remelt either.

Ross

Offline pwalsh

  • !!!
  • Sr. Member
  • ****
  • Posts: 473
Re: Silicone printing and curing
« Reply #2 on: March 19, 2016, 04:35:50 PM »
I am really keep to  print with silicone, we get a lot of synthetic fleece that is a nightmare to print.
I watched a clip on UTube, they printed with Dow Corning inks and cured at 150C for one min,  we cure plastisol at 160C for 2 min.     The Rutland site mentions a much lower temperature, this is a big problem for us because we are running 2 carousels through one oven and it's a real PITA to change the temperature.
Does anyone have any experience with this?     Can you cure Silicone hotter for less time?

Maxie:  I'm not confident enough to give you an absolutely certain answer to your question; "Can you cure Silicone inks for a shorter time at Plastisol Cure Temps"  What I can tell you is we have exhibited at multiple trade shows where we have used a single dryer to cure both water based DTG inks for 3 - 4 minutes, and silicone screen inks for less than a minute at a higher temperature. 

With Rob Coleman "busting it" at the Atlantic City ISS Show this weekend, he might be a little slow getting back with a qualified response.  I've forwarded this question to a couple of our Nazdar SourceOne Technical Application Specialists and a Product Expert from DOW Corning, and I expect that someone will get back to TSB with a response.  I've attached a copy of the ImageStar Silicone Application Guide for reference.
« Last Edit: March 19, 2016, 04:46:27 PM by pwalsh »
Peter G. Walsh - Executive Vice President
The M&R Companies - Roselle, IL USA
Email:  peter.walsh@mrprint.com
Office 847-410-3445 / Cell 913-579-6662

Offline Maxie

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1328
Re: Silicone printing and curing
« Reply #3 on: March 19, 2016, 05:12:54 PM »
Thanks Peter
Maxie Garb.
T Max Designs.
Silk Screen Printers
www.tmax.co.il

Offline Carl Busey

  • Newbie
  • *
  • Posts: 1
Re: Silicone printing and curing
« Reply #4 on: March 20, 2016, 08:51:01 PM »
Hi Maxie,
This is Carl Busey with Nazdar, I just wanted to weigh in on you question regarding the cure temp of the IMS Silicone ink from Nazdar. You are better off curing the IMS silicone  at 260* F  at a minute retention time in the dryer.  Although you are able to cure at higher temperatures like your plastisol inks, it will greatly reduce the products dye migration properties. If you would like to talk about this in detail you can call me on my cellphone. I will private message you my number. Hope this helps...

Carl

Offline Frog

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 13980
  • Docendo discimus
Re: Silicone printing and curing
« Reply #5 on: March 20, 2016, 09:26:49 PM »
Thanks Maxie, you helped draw out our second three year member, first time poster!
And thanks to you as well, Carl. Better late than never  :D
That rug really tied the room together, did it not?

Offline pwalsh

  • !!!
  • Sr. Member
  • ****
  • Posts: 473
Re: Silicone printing and curing
« Reply #6 on: March 21, 2016, 06:11:49 AM »
Thanks Maxie, you helped draw out our second three year member, first time poster!
And thanks to you as well, Carl. Better late than never  :D

Frog; Now that Maxie has lured Carl out from the shadows and into the light, lets hope we can convince him to be an active contributor to TSB.
Peter G. Walsh - Executive Vice President
The M&R Companies - Roselle, IL USA
Email:  peter.walsh@mrprint.com
Office 847-410-3445 / Cell 913-579-6662

Offline AAMike

  • Full Member
  • ***
  • Posts: 207
Re: Silicone printing and curing
« Reply #7 on: March 21, 2016, 07:25:45 AM »
You could always flash cure it to the touch and then wait 24 hours for it to fully cure. I would not recommend curing it at high temps. That goes against keeping your poly from releasing dye. This might work on some garments but I would be against it in principle.

Offline pwalsh

  • !!!
  • Sr. Member
  • ****
  • Posts: 473
Re: Silicone printing and curing
« Reply #8 on: March 21, 2016, 07:59:54 PM »
You could always flash cure it to the touch and then wait 24 hours for it to fully cure. I would not recommend curing it at high temps. That goes against keeping your poly from releasing dye. This might work on some garments but I would be against it in principle.

Good advice Mike
Peter G. Walsh - Executive Vice President
The M&R Companies - Roselle, IL USA
Email:  peter.walsh@mrprint.com
Office 847-410-3445 / Cell 913-579-6662

Offline Larry Tywater

  • Newbie
  • *
  • Posts: 5
Re: Silicone printing and curing
« Reply #9 on: March 23, 2016, 10:58:17 AM »
Peter, I am slowly trying to do my part as well!
Larry Tywater
Chromaline Screen Print Products
Technical Sales Rep
Southeast/Southcentral/ Texas
www.chromaline.com 800-328-4261

Offline pwalsh

  • !!!
  • Sr. Member
  • ****
  • Posts: 473
Re: Silicone printing and curing
« Reply #10 on: March 23, 2016, 08:36:25 PM »
Peter, I am slowly trying to do my part as well!

Larry:  Thank you so much for joining the TSB Community.

It's great to have another screen-printing professional join the boards.

I'm confident that you will find many opportunities to contribute to the dialogue here.
« Last Edit: March 23, 2016, 08:40:26 PM by pwalsh »
Peter G. Walsh - Executive Vice President
The M&R Companies - Roselle, IL USA
Email:  peter.walsh@mrprint.com
Office 847-410-3445 / Cell 913-579-6662