Author Topic: Hep! I need to fix this misprint  (Read 2188 times)

Offline Shanarchy

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1421
Hep! I need to fix this misprint
« on: December 04, 2015, 03:57:54 PM »
I just printed 40 hoodies up that I need to deliver in the AM.

That letter is an A. I'm missing the little line that closes it up. Suggestions of how I can fix this? I can't deliver them like this, and I can't show up empty handed.


Offline Frog

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 13980
  • Docendo discimus
Re: Hep! I need to fix this misprint
« Reply #1 on: December 04, 2015, 04:11:29 PM »
How are you with a toothpick or needle as a touch-up tool??

I also wear reading glasses while doing this type of thing
That rug really tied the room together, did it not?

Offline Croft

  • Hero Member
  • *****
  • Posts: 875
Re: Hep! I need to fix this misprint
« Reply #2 on: December 04, 2015, 04:21:02 PM »
shoot a screen with a better a and print one by one wiping between every shirt , with white on black it should be easy to print , and since its so skinny you'll probably get away with one hit

Offline 1964GN

  • Hero Member
  • *****
  • Posts: 833
Re: Hep! I need to fix this misprint
« Reply #3 on: December 04, 2015, 04:21:05 PM »
What Frog said ^

Offline Screened Gear

  • Gonzo Member
  • ******
  • Posts: 2580
Re: Hep! I need to fix this misprint
« Reply #4 on: December 04, 2015, 04:24:03 PM »
I have used a paint brush before... Just cut the brush part down to about a 1/8 of an inch. This way the bristles are hard and make moving, painting the ink easy. It also makes it easier to get a sharp edge. If you were doing a long line, I use a business card as a guide and shield. It takes some time but if done right no one would know. You may have to send it down the dryer and come back and try to fix it again. Take your time.  I have done about everything to fix mistakes since I hired a printer.

Offline DannyGruninger

  • Gonzo Member
  • ******
  • Posts: 1220
Re: Hep! I need to fix this misprint
« Reply #5 on: December 04, 2015, 04:27:36 PM »
I would cut some vinyl as a template/mask....... lay it over the area then put the ink down, pull the mask up and your done....... Kinda like how people use stencils to paint shapes/designs, etc on walls(if that makes sense)


Danny Gruninger
Denver Print House / Lakewood Colorado
https://www.instagram.com/denverprinthouse

Offline mimosatexas

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4221
  • contributor
Re: Hep! I need to fix this misprint
« Reply #6 on: December 04, 2015, 04:42:31 PM »
if it is a straight line, use a clean up card cut to the width you need and dip it in ink then press it on the shirt maybe?

Offline Frog

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 13980
  • Docendo discimus
Re: Hep! I need to fix this misprint
« Reply #7 on: December 04, 2015, 04:59:02 PM »
I would cut some vinyl as a template/mask....... lay it over the area then put the ink down, pull the mask up and your done....... Kinda like how people use stencils to paint shapes/designs, etc on walls(if that makes sense)


In that vein, how about my eraser guard already re-purposed for spot removing?
That rug really tied the room together, did it not?

Offline kingscreen

  • Gonzo Member
  • ******
  • Posts: 1161
Re: Hep! I need to fix this misprint
« Reply #8 on: December 04, 2015, 05:01:26 PM »
Masking tape.  Clean up card cut in half.  Boom.
Scott Garnett
King Screen

Offline Squeegie

  • !!!
  • Full Member
  • ***
  • Posts: 177
Re: Hep! I need to fix this misprint
« Reply #9 on: December 04, 2015, 05:17:14 PM »
^^^^^^^^   
^^^^^^^^

Winner winner!!

Offline Shanarchy

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1421
Re: Hep! I need to fix this misprint
« Reply #10 on: December 04, 2015, 05:28:16 PM »
I like the way you think King!

Yeah, its just a skinny straight line, I was going to put some tape on a screen and line it up in place but this idea seems easiest. The tape won't pull at the ink, will it?

Just the dryer will be fine? Or should I heat press it after too to make sure it's in there?

Offline Sbrem

  • Ludicrous Speed Member
  • *******
  • Posts: 6055
Re: Hep! I need to fix this misprint
« Reply #11 on: December 05, 2015, 11:18:15 AM »
I would use the original screen, clean, as a line up guide to get the offending letter in place on the press (we are talking a manual press, right?), then a second screen with just the one shape to print in black, registered of course, and just print it...

Steve
I made a mistake once; I thought I was wrong about something; I wasn't

Offline GaryG

  • !!!
  • Hero Member
  • *****
  • Posts: 750
Re: Hep! I need to fix this misprint
« Reply #12 on: December 05, 2015, 05:08:48 PM »
Yeah I've done this second screen before - but like Frog's approach, I find the back of an exacto knife blade will be very quick and precise.  Reading glasses too.