Author Topic: How many colors would this take? (hands) (Read 2606 times)

Gilligan · « **on:** February 09, 2015, 07:00:12 PM »

Here is another one of these "how many colors".

This is going on black and will have some white text.

I'm seeing 8 obvious colors (white, black and the colors of each hand).

Could these be done with some simulation of colors or is it a case of being so large of an area for each color it should be independent colors?

3Deep · « **Reply #1 on:** February 09, 2015, 07:51:02 PM »

Dottonedan · « **Reply #2 on:** February 09, 2015, 08:34:08 PM »

Hands down...

this is an easy one for 4 color process (+ 2 whites) on darks. Use white underbase. Print heavy,base like a 110, then flash, then print another high mesh white on top to smooth it out, Flash that. Then top colors YMCK. Make sure the base is a smooth bright white base.

This art consist of process colors. Bright or leaning towards true process, so if you choose to go sim process, you might consider adding some neon to those pms spot colors.

Additional note. If process + spots, then make the spots the purple and the green. Those are 2ndary colors and tend to shift in process color. Reds, come out fine.

mimosatexas · « **Reply #3 on:** February 09, 2015, 08:53:38 PM »

Can definitely do this as cmyk. Even though you have large areas, they are relatively even tones (color-wise) and all of the gradients will be determined by your base (use the black of the shirt instead of black ink) and highlight white.

Sbrem · « **Reply #4 on:** February 10, 2015, 01:24:39 PM »

I see it as CMYK w/2 whites, but I'd rather go 2 whites, 6 spots and black if I had my druthers... if money and equipment is not a factor.

Steve

Gilligan · « **Reply #5 on:** February 10, 2015, 03:04:17 PM »

Six color press (with flash back) is what we have in house... After that it gets sent to Alan.

ebscreen · « **Reply #6 on:** February 10, 2015, 03:38:25 PM »

Personally I'd shy away from CMYK on this. Base plus 6 colors minimum, add black and top white if you can.
Art is too "clean" for process IMO.

UltraSeps · « **Reply #7 on:** February 10, 2015, 05:46:50 PM »

I looked at this post yesterday and thought about it for a while, and although I'm usually in the camp of less-is-more, there's 6 clearly defined, large areas of color identity in this art that needs to be considered. Trying to cut this back using process color would be difficult to control, IMO. Therefore, if I was printing it, I'd go with max colors so it matches the original. Base, 6 top colors, highlight, black.

Fluid · « **Reply #8 on:** February 12, 2015, 06:06:11 PM »

The toughest color would be that red yet with the right edits ymck should do just fine like DTDan mentioned.

Richard Reilly - Fluid

News:

Author Topic: How many colors would this take? (hands) (Read 2606 times)

Gilligan

How many colors would this take? (hands)

3Deep

Re: How many colors would this take? (hands)

Dottonedan

Re: How many colors would this take? (hands)

mimosatexas

Re: How many colors would this take? (hands)

Sbrem

Re: How many colors would this take? (hands)

Gilligan

Re: How many colors would this take? (hands)

ebscreen

Re: How many colors would this take? (hands)

UltraSeps

Re: How many colors would this take? (hands)

Fluid

Re: How many colors would this take? (hands)